LCE1500T is a one-part, heat-curable thermally conductive silicone gel featuring a thermal conductivity of 15 ± 0.5 W/m·K. It is designed to bridge gaps between heat-generating electronic components and cooling structures, providing a conductive path for heat dissipation.
The material is dispensed directly onto the assembly, where it conforms to mating surfaces and accommodates variations in component height and interface geometry. After curing at 100°C for 60 minutes, LCE1500T forms a compliant silicone elastomer with a hardness of 70 ± 10 Shore OO, creating a thermal interface shaped to the assembled components.
By filling interface voids and improving effective surface contact, LCE1500T helps reduce thermal contact resistance. Its one-part formulation supports automated dispensing without two-component proportioning or mixing, simplifying material preparation for production.
|
Test Items |
Unit |
LCE1500T |
Test Standard |
|
Appearance |
- |
Gray |
Visual |
|
Density |
g/cm3 |
3.50±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥20 |
φ2.54mm/90psi |
|
BLT |
μm |
≤200 |
- |
|
Hardness |
Shore OO |
70±10 |
ASTM D2240 |
|
Dielectric Strength |
KV/mm |
≥6 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1012 |
ASTM D257 |
|
Weight Loss |
% |
≤0.3 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
15.0±0.5 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
15.0±0.5 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.054 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.350 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.780 |
ASTM E1269 |
With a thermal conductivity of 15 W/m·K, LCE1500T supports heat transfer across interfaces in electronic assemblies with demanding thermal management requirements.
The dispensable material follows surface contours and fills assembly gaps, helping establish contact between components and heat sinks, cooling plates, or housings.
Heat curing forms an elastomeric thermal interface within the assembly, combining flexible material placement with pad-like performance after curing.
No two-component mixing is required, allowing straightforward material preparation and integration into automated dispensing workflows.
Designed for applications requiring low assembly pressure, LCE1500T helps establish thermal contact while accommodating dimensional tolerances. Final mechanical loading depends on the interface design and processing conditions.
Application Areas
Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.
Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.
Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.
|
Test Items |
Unit |
LCE1500T |
Test Standard |
|
Appearance |
- |
Gray |
Visual |
|
Density |
g/cm3 |
3.50±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥20 |
φ2.54mm/90psi |
|
BLT |
μm |
≤200 |
- |
|
Hardness |
Shore OO |
70±10 |
ASTM D2240 |
|
Dielectric Strength |
KV/mm |
≥6 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1012 |
ASTM D257 |
|
Weight Loss |
% |
≤0.3 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
15.0±0.5 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
15.0±0.5 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.054 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.350 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.780 |
ASTM E1269 |
Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.
Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.
Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.
With a thermal conductivity of 15 W/m·K, LCE1500T supports heat transfer across interfaces in electronic assemblies with demanding thermal management requirements.
The dispensable material follows surface contours and fills assembly gaps, helping establish contact between components and heat sinks, cooling plates, or housings.
Heat curing forms an elastomeric thermal interface within the assembly, combining flexible material placement with pad-like performance after curing.
No two-component mixing is required, allowing straightforward material preparation and integration into automated dispensing workflows.
Designed for applications requiring low assembly pressure, LCE1500T helps establish thermal contact while accommodating dimensional tolerances. Final mechanical loading depends on the interface design and processing conditions.
Tel:+86-13691979380
+86-19065180554
E-mail:elvinlen@szutd.com
Carly@szutd.com
Address:8th Floor, Tower B, Lechuanghui Building, No. 1211 Guanguang Road, Longhua District, Shenzhen City, Guangdong Province