Thermal Gel
  • LCE1200T 12 W/m·K Post-curing one component high thermal conductivity gel
  • LCE1200T.png
  • Post-curing one-part thermal conductive gel.jpg
  • LCE1200T 12 W/m·K Post-curing one component high thermal conductivity gel
  • LCE1200T.png
  • Post-curing one-part thermal conductive gel.jpg

LCE1200T 12 W/m·K Post-curing one component high thermal conductivity gel

Specification:
Thermal Conductivity:12±0.5 W/m·K
Thermal Impedance:0.070 ℃·in²/W
Cure:100℃/60min
Extrusion Rate:≥20 g/min
BLT:≤300 μm
Hardness:60±10 Shore OO
Introduction:
LCE1200T 12 W/m·K One-Part Thermally Conductive Silicone Gel
LCE1200T is a one-part, heat-curable thermal gap filler with a thermal conductivity of 12 ± 0.5 W/m·K. Designed for electronic assemblies with demanding heat transfer requirements, it provides a conformable interface between heat-generating components and heat sinks, cooling plates, or module housings.
  • Product introduction
  • Technical Parameters
  • Product Application
  • Product Characteristics

LCE1200T 12 W/m·K One-Part Thermally Conductive Silicone Gel


High Thermal Conductivity with Dispensable Processing


LCE1200T is a one-part, heat-curable thermal gap filler with a thermal conductivity of 12 ± 0.5 W/m·K. Designed for electronic assemblies with demanding heat transfer requirements, it provides a conformable interface between heat-generating components and heat sinks, cooling plates, or module housings.


Before curing, the dispensable silicone gel adapts to surface irregularities and fills gaps between mating parts. A curing cycle of 100°C for 60 minutes transforms the material into a soft elastomer with a hardness of 60 ± 10 Shore OO. This allows the thermal interface to form around the assembly geometry, providing pad-like compliance after curing.


LCE1200T supports low-pressure assembly and helps improve effective surface contact. Its gap-filling capability reduces air voids at the interface, helping limit thermal contact resistance while accommodating component height variations and assembly tolerances.

Test Items

Unit

LCE1200T

Test Standard

Appearance

-

Gray

Visual

Density

g/cm3

3.50±0.2

ASTM D792

Extrusion Rate

g/min

≥20

φ2.54mm/90psi

BLT

μm

≤200

-

Hardness

Shore OO

60±10

ASTM D2240

Dielectric Strength

KV/mm

≥6

ASTM D149

Volume Resistivity

Ω·cm

≥1×1012

ASTM D257

Weight Loss

%

≤0.3

150℃240H

Thermal Conductivity

W/m·K

12.0±0.5

ISO 22007-2

Thermal Conductivity

W/m·K

12.0±0.5

ASTM D5470(Three-Thickness Fit)

Thermal Impedance

℃·in²/W

0.070

ASTM D5470(0.1mm )

Thermal Impedance

℃·cm²/W

0.450

ASTM D5470(0.1mm )

Operating Temperature

℃

-40~150

-

Specific Heat Capacity

J/(g/K)

0.780

ASTM E1269


Key Features and Advantages


12 W/m·K Thermal Conductivity

Provides a conductive heat transfer path from electronic components to cooling structures for applications with demanding thermal requirements.


Dispense-to-Shape Application

Allows material placement to follow component footprints and interface geometries, supporting assemblies with uneven surfaces or varying component heights.


One-Part Formulation

Requires no two-component proportioning or mixing, simplifying material preparation and integration into dispensing processes.


Heat-Cured Elastomeric Interface

Forms a soft silicone elastomer after heating, combining the placement flexibility of a dispensable gap filler with a compliant cured structure.


Low Assembly Stress

Designed to establish thermal contact under low assembly pressure, helping limit mechanical loading on sensitive components.


Automated Dispensing Compatibility

Supports automated material application for electronic production, with dispensing parameters selected to suit the equipment and assembly requirements.


Application Areas


Computing and server hardware: Thermal interfaces in CPU- and GPU-based systems, servers, and associated cooling assemblies.



Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.


Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.


Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.


Test Items

Unit

LCE1200T

Test Standard

Appearance

-

Gray

Visual

Density

g/cm3

3.50±0.2

ASTM D792

Extrusion Rate

g/min

≥20

φ2.54mm/90psi

BLT

μm

≤200

-

Hardness

Shore OO

60±10

ASTM D2240

Dielectric Strength

KV/mm

≥6

ASTM D149

Volume Resistivity

Ω·cm

≥1×1012

ASTM D257

Weight Loss

%

≤0.3

150℃240H

Thermal Conductivity

W/m·K

12.0±0.5

ISO 22007-2

Thermal Conductivity

W/m·K

12.0±0.5

ASTM D5470(Three-Thickness Fit)

Thermal Impedance

℃·in²/W

0.070

ASTM D5470(0.1mm )

Thermal Impedance

℃·cm²/W

0.450

ASTM D5470(0.1mm )

Operating Temperature

℃

-40~150

-

Specific Heat Capacity

J/(g/K)

0.780

ASTM E1269

Application Areas


Computing and server hardware: Thermal interfaces in CPU- and GPU-based systems, servers, and associated cooling assemblies.



Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.


Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.


Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.

Key Features and Advantages


12 W/m·K Thermal Conductivity

Provides a conductive heat transfer path from electronic components to cooling structures for applications with demanding thermal requirements.


Dispense-to-Shape Application

Allows material placement to follow component footprints and interface geometries, supporting assemblies with uneven surfaces or varying component heights.


One-Part Formulation

Requires no two-component proportioning or mixing, simplifying material preparation and integration into dispensing processes.


Heat-Cured Elastomeric Interface

Forms a soft silicone elastomer after heating, combining the placement flexibility of a dispensable gap filler with a compliant cured structure.


Low Assembly Stress

Designed to establish thermal contact under low assembly pressure, helping limit mechanical loading on sensitive components.


Automated Dispensing Compatibility

Supports automated material application for electronic production, with dispensing parameters selected to suit the equipment and assembly requirements.

Contact

Tel:+86-13691979380
+86-19065180554

E-mail:elvinlen@szutd.com
Carly@szutd.com

Address:8th Floor, Tower B, Lechuanghui Building, No. 1211 Guanguang Road, Longhua District, Shenzhen City, Guangdong Province