LCE800T is a one-part, heat-curable thermally conductive silicone gel designed to create a conformable thermal interface between electronic components and cooling structures. With a thermal conductivity of 8 ± 0.3 W/m·K, it helps transfer heat from heat-generating components to heat sinks, cooling plates, and other thermal management assemblies.
The dispensable formulation fills interface gaps and follows uneven surface profiles during assembly. After curing at 100°C for 60 minutes, LCE800T forms a soft silicone elastomer that combines the application flexibility of a dispensed material with a compliant, pad-like thermal interface.
Designed for low-stress assembly, LCE800T accommodates dimensional variations and improves contact between mating surfaces. By filling air gaps, it helps increase the effective heat transfer area and reduce thermal contact resistance.
|
Test Items |
Unit |
LCE800T |
Test Standard |
|
Appearance |
- |
Gray |
Visual |
|
Density |
g/cm3 |
3.30±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥20 |
φ2.54mm/90psi |
|
BLT |
μm |
≤150 |
- |
|
Hardness |
Shore OO |
50±10 |
ASTM D2240 |
|
Dielectric Strength |
KV/mm |
≥6 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1013 |
ASTM D257 |
|
Weight Loss |
% |
≤0.3 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
8.0±0.3 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
8.0±0.3 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.060 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.375 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.780 |
ASTM E1269 |
The thermally conductive silicone formulation fills air gaps and improves contact between mating surfaces, helping reduce thermal contact resistance.
After curing, LCE500T forms a soft elastomer that accommodates surface irregularities and dimensional tolerances while limiting stress on sensitive electronic components.
The one-part format eliminates the need for two-component proportioning and mixing. Dispensing allows material placement to match component layouts and gap geometries.
Combines thermal conduction with electrical insulation and resistance to high and low temperatures for electronic thermal management applications.
Sag resistance helps retain material placement before curing, while the cured elastomer provides a compliant interface for assemblies exposed to vibration.
Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.
Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.
Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.
|
Test Items |
Unit |
LCE800T |
Test Standard |
|
Appearance |
- |
Gray |
Visual |
|
Density |
g/cm3 |
3.30±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥20 |
φ2.54mm/90psi |
|
BLT |
μm |
≤150 |
- |
|
Hardness |
Shore OO |
50±10 |
ASTM D2240 |
|
Dielectric Strength |
KV/mm |
≥6 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1013 |
ASTM D257 |
|
Weight Loss |
% |
≤0.3 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
8.0±0.3 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
8.0±0.3 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.060 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.375 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.780 |
ASTM E1269 |
Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.
Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.
Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.
The thermally conductive silicone formulation fills air gaps and improves contact between mating surfaces, helping reduce thermal contact resistance.
After curing, LCE500T forms a soft elastomer that accommodates surface irregularities and dimensional tolerances while limiting stress on sensitive electronic components.
The one-part format eliminates the need for two-component proportioning and mixing. Dispensing allows material placement to match component layouts and gap geometries.
Combines thermal conduction with electrical insulation and resistance to high and low temperatures for electronic thermal management applications.
Sag resistance helps retain material placement before curing, while the cured elastomer provides a compliant interface for assemblies exposed to vibration.
Tel:+86-13691979380
+86-19065180554
E-mail:elvinlen@szutd.com
Carly@szutd.com
Address:8th Floor, Tower B, Lechuanghui Building, No. 1211 Guanguang Road, Longhua District, Shenzhen City, Guangdong Province