LCE500T is a one-part, dispensable thermal conductive silicone gel engineered to transfer heat between electronic components and cooling structures. Featuring a thermal conductivity of 5 ± 0.3 W/m·K and a thermal impedance of 0.033 °C·in²/W, it supports thermal management in assemblies where efficient heat transfer and low mechanical stress are essential.
Applied as a dispensable gap filler, LCE500T conforms to mating surfaces and fills interface gaps before curing. Heating at 100°C for 60 minutes converts the material into a soft silicone elastomer, creating a compliant thermal interface between the component and its heat sink or cooling plate.
Its one-part formulation requires no two-component mixing and supports automated dispensing. With an extrusion rate of ≥ 200 g/min under specified test conditions, LCE500T is suitable for production processes requiring consistent material application.
|
Test Items |
Unit |
LCE500T |
Test Standard |
|
Appearance |
- |
Gray |
Visual |
|
Density |
g/cm3 |
3.29±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥80 |
φ2.54mm/90psi |
|
BLT |
μm |
≤40 |
- |
|
Hardness |
Shore OO |
50±10 |
ASTM D2240 |
|
Dielectric Strength |
KV/mm |
≥7 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1013 |
ASTM D257 |
|
Weight Loss |
% |
≤0.3 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
5.0±0.3 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
5.0±0.3 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.033 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.213 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.784 |
ASTM E1269 |
The thermally conductive silicone formulation fills air gaps and improves contact between mating surfaces, helping reduce thermal contact resistance.
After curing, LCE500T forms a soft elastomer that accommodates surface irregularities and dimensional tolerances while limiting stress on sensitive electronic components.
The one-part format eliminates the need for two-component proportioning and mixing. Dispensing allows material placement to match component layouts and gap geometries.
Combines thermal conduction with electrical insulation and resistance to high and low temperatures for electronic thermal management applications.
Sag resistance helps retain material placement before curing, while the cured elastomer provides a compliant interface for assemblies exposed to vibration.
Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.
Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.
Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.
|
Test Items |
Unit |
LCE500T |
Test Standard |
|
Appearance |
- |
Gray |
Visual |
|
Density |
g/cm3 |
3.29±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥80 |
φ2.54mm/90psi |
|
BLT |
μm |
≤40 |
- |
|
Hardness |
Shore OO |
50±10 |
ASTM D2240 |
|
Dielectric Strength |
KV/mm |
≥7 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1013 |
ASTM D257 |
|
Weight Loss |
% |
≤0.3 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
5.0±0.3 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
5.0±0.3 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.033 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.213 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.784 |
ASTM E1269 |
Power conversion and amplification: Gap filling between power modules, power semiconductors, power amplifiers, and heat dissipation structures.
Telecommunications infrastructure: Thermal management for base stations, 5G equipment, and networking electronics.
Automotive electronic modules: Heat transfer from battery management systems (BMS), vehicle control modules, and other heat-generating components to cooling structures.
The thermally conductive silicone formulation fills air gaps and improves contact between mating surfaces, helping reduce thermal contact resistance.
After curing, LCE500T forms a soft elastomer that accommodates surface irregularities and dimensional tolerances while limiting stress on sensitive electronic components.
The one-part format eliminates the need for two-component proportioning and mixing. Dispensing allows material placement to match component layouts and gap geometries.
Combines thermal conduction with electrical insulation and resistance to high and low temperatures for electronic thermal management applications.
Sag resistance helps retain material placement before curing, while the cured elastomer provides a compliant interface for assemblies exposed to vibration.
Tel:+86-13691979380
+86-19065180554
E-mail:elvinlen@szutd.com
Carly@szutd.com
Address:8th Floor, Tower B, Lechuanghui Building, No. 1211 Guanguang Road, Longhua District, Shenzhen City, Guangdong Province