LCE600 is a silicone-based, one component thermal conductive gel designed for efficient thermal management in high-power electronic devices. With a thermal conductivity of 6.0 ± 0.3 W/m·K, it facilitates heat transfer from electronic components to heat sinks or enclosures while providing good electrical insulation.
Its soft, paste-like consistency enables effective gap filling and thermal contact under low pressure. Ready to use without mixing, LCE600 simplifies material preparation and application. With stable performance over an operating temperature range of -40 to 150 °C, it supports efficient cooling and long-term, stable device operation.
|
Test Items |
Unit |
LCE600 |
Test Standard |
|
Appearance |
- |
Blue |
Visual |
|
Density |
g/cm3 |
3.38±0.2 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥40 |
φ2.54mm/90psi |
|
BLT |
μm |
≤150 |
- |
|
Dielectric Strength |
KV/mm |
≥5 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
≥1×1012 |
ASTM D257 |
|
Weight Loss |
% |
≤0.2 |
150℃240H |
|
Thermal Conductivity |
W/m·K |
6.0±0.3 |
ISO 22007-2 |
|
Thermal Conductivity |
W/m·K |
6.0±0.3 |
ASTM D5470(Three-Thickness Fit) |
|
Thermal Impedance |
℃·in²/W |
0.024 |
ASTM D5470(0.1mm ) |
|
Thermal Impedance |
℃·cm²/W |
0.154 |
ASTM D5470(0.1mm ) |
|
Operating Temperature |
℃ |
-40~150 |
- |
|
Specific Heat Capacity |
J/(g/K) |
0.625 |
ASTM E1269 |
Material characteristics: Non-volatile, non-corrosive, environmentally friendly, and non-toxic.
Solar photovoltaic modules: Provides thermal conduction in solar photovoltaic applications.
For buyers evaluating a thermal conductive gel factory or a one component thermal conductive gel manufacturer, LCE600 provides clearly specified thermal and application parameters to support material selection. Its thermal conductivity, thermal impedance, extrusion rate, bond line thickness, and operating temperature range offer a practical basis for assessing suitability for electronic cooling and gap-filling requirements.
Evaluate LCE600 under the intended application conditions to confirm compatibility with your assembly and thermal management requirements.
|
Test Item |
Unit | LCE600 | Test Methods |
|
Color |
- |
Blue |
Visually |
|
Specific Gravity |
g/cc |
3.38 |
ASTM D792 |
|
Extrusion Rate |
g/min |
≥15 |
φ2.54mm 90psi |
|
Thickness After Compression |
mm |
0.2 |
- |
|
Weight Loss |
% |
≤0.2 |
@150℃240H |
|
Breakdown Voltage |
KV/mm |
≥5 |
ASTM D149 |
|
Volume Resistivity |
Ω·cm |
1×1012 |
ASTM D257 |
|
Continuous Use Temp |
℃ |
-40~150 |
- |
|
Thermal Conductivity |
W/m·K |
6.0 |
ISO 22007-2 |
|
Thermal impedance |
℃·in2 /W |
0.024 |
ASTM D5470 |
Tel:+86-13691979380
+86-19065180554
E-mail:elvinlen@szutd.com
Carly@szutd.com
Address:8th Floor, Tower B, Lechuanghui Building, No. 1211 Guanguang Road, Longhua District, Shenzhen City, Guangdong Province