Thermal Gel
  • LCE380 One Component Thermal Conductive Gel
  • LCE200导热凝胶7.jpg
  • LCE200导热凝胶8.jpg
  • LCE200导热凝胶9.jpg
  • LCE200导热凝胶10.jpg
  • LCE300导热凝胶7.jpg
  • LCE300导热凝胶8.jpg
  • LCE300导热凝胶9.jpg
  • LCE300导热凝胶10.jpg
  • LCE380导热凝胶7.jpg
  • LCE380 One Component Thermal Conductive Gel
  • LCE200导热凝胶7.jpg
  • LCE200导热凝胶8.jpg
  • LCE200导热凝胶9.jpg
  • LCE200导热凝胶10.jpg
  • LCE300导热凝胶7.jpg
  • LCE300导热凝胶8.jpg
  • LCE300导热凝胶9.jpg
  • LCE300导热凝胶10.jpg
  • LCE380导热凝胶7.jpg

LCE380 One Component Thermal Conductive Gel

Specification:
30ml, 55ml, 300ml or Customized
Introduction:
Single component thermal conductive gel is a kind of thermal conductive material with lower deformation force. It has similar plasticity of plasticized, non flowing, high thermal conductivity and low thermal resistance. It has good insulation, good insulation, and can fill the gap automatically, so that the contact area can reach full contact. It can be applied to the heat dissipation module or electronic component with larger thickness. Unlike thermal conductive silicone grease, heat conductive gel has no sedimentation and no flow phenomenon. It is suitable for screen printing or scraping. The syringe packaging can be dispensed on standard dispensing equipment, so as to effectively improve operation convenience and efficiency.
  • Product introduction
  • Technical Parameters
  • Product Application
  • Product Characteristics
Single component thermal conductive gel is a kind of thermal conductive material with lower deformation force. It has similar plasticity of plasticized, non flowing, high thermal conductivity and low thermal resistance. It has good insulation, good insulation, and can fill the gap automatically, so that the contact area can reach full contact. It can be applied to the heat dissipation module or electronic component with larger thickness. Unlike thermal conductive silicone grease, heat conductive gel has no sedimentation and no flow phenomenon. It is suitable for screen printing or scraping. The syringe packaging can be dispensed on standard dispensing equipment, so as to effectively improve operation convenience and efficiency.
Test Item
Unit LCE380 Test Methods
Color
- Pink
Visually
Specific Gravity
g/cc
3.39 ASTM D792
Extrusion Rate
g/min
≥40
φ2.54mm 90psi
Thickness After Compression
mm
0.1
-
Weight Loss
% ≤0.2
@150℃240H
Breakdown Voltage
KV/mm
≥7
ASTM D149
Volume Resistivity
Ω·cm
1×1013
ASTM D257
Continuous Use Temp

-40~150
-
Thermal Conductivity
W/m·K
3.8 ISO 22007-2
Thermal impedance
℃·in2 /W
0.046
ASTM D5470
Wireless electronic equipment
Communication electronic hardware equipment
Automotive electronic application equipment
Chassis or related heat dissipation module
Host or small office network equipment
Microprocessors, memory chips and graphics processors
High thermal conductivity, low thermal resistance, good wettability
No settlement, no flow, can fill any uneven gap
Soft, no stress, can be compressed to 0.1 mm thin
The design and application are convenient, and the automatic dispensing can adjust the size of any thickness

Contact

Tel:+86-13691979380

E-mail:ElvinLen@szutd.com

Address:Union Tenda Technology Park, No. 61, Zhangqi Road, Guixiang Community,Guanlan Street, Longhua District, Shenzhen